Dyson Not Working After Cleaning Filter: Solved!

If your Dyson V6, V8, V10, V11, or V12 isn’t working after cleaning the filter, it might not have been installed correctly. To resolve this, you should install the filter correctly. Then, a wet filter can prevent your vacuum from functioning properly. 

If the motor head fails after filter cleaning, it may be due to a wet filter causing moisture damage to the motor’s electrical components. In such cases, you may need to replace the motor head.

That’s not all. There are more reasons responsible for Dyson not working after cleaning filter. Hang tight on the article to learn all of the reasons and solutions. 

Dyson Not Working after Cleaning Filter: Top Reasons And Solution

If your Dyson V6, V8, V10,  V11, and V12 are not working even after cleaning the filter, there might be some reasons behind this. Here are seven top reasons which are primarily responsible for this. 

Before going to discuss them, Let’s have a quick picture of the reasons and solutions. 

Reason	Solution
Improper filter installation	Ensure proper installation
Wet Filter	Make sure to dry out completely
Clogged or dirty filter	Clean the filter properly
Filter motorhead failure	Replace the motor
Battery damage	Replace your Dyson Battery
Inside obstructions	Check for any damage

Now it’s time to move on to the detailed discussion of each of the reasons along with the solution in a detailed manner.

Reason 1: Improper Filter Installation

If you find that you can’t access your Dyson V6, V8, V10, V11, and V12, after cleaning the filter, it’s likely because the filter unit wasn’t installed correctly. 

After cleaning the Dyson vacuum filter, it’s essential to attach it by twisting the cap clockwise until it clicks. 

However, if the filter unit isn’t correctly installed, the vacuum won’t operate. An incorrectly installed filter unit is indicated by a flashing blue light on the vacuum’s side.

Solution:

To resolve this problem, you need to install the filter correctly. To do that follow the steps below.

Step 1: First, remove the filter unit from the vacuum. Then, examine the areas where the filter unit makes contact with the vacuum. 

Here try to ensure there’s no debris hindering the filter from locking securely in place.

Step 2: Next, firmly press the filter unit into position and rotate it clockwise until you hear an audible click. 

This may require some effort due to the rubber gasket designed to create an airtight seal with no gaps between the filter and the vacuum unit.

Reason 2: Wet Filter

If the filter remains damp after cleaning, your Dyson V6, V8, V10, V11, and V12 vacuum cleaner might not function properly.

Most of the time it happens because, according to Dyson’s guidelines, they asked to rinse the filter under a cold water tap. However, a common oversight is not allowing the filter sufficient time to completely dry afterward. 

A damp filter obstructs the airflow, leading to the Dyson’s protective mechanism preventing it from operating to avoid potential damage.

Solution:

To get over the situation, it’s imperative to remove it immediately and allow it to air dry overnight.

Dyson’s recommendation is to thoroughly wash the filter and then grant it a full 24 hours for complete drying. This extended drying time may pose a challenge if you intend to use the vacuum for additional cleaning on the same day, so plan accordingly.

Do not use hair dryers or heat guns on the filter, and do not expose it to direct sunlight. Instead, opt for the most effective approach: place the filter in a well-ventilated area, allowing it to air dry naturally and be ready for normal use.

Reason 3: Clogged or Dirty Filter

A frequent reason is having a dirty or clogged filter. Dyson vacuum cleaners are manufactured with HEPA filter systems offering awesome benefits.

That is designed to capture 99.97% of particles, such as dust, pollen, and bacteria. Over time, these particles can clog the filter, diminishing suction power. Clogging is also a reason for the Dyson DC33 brush not spinning.

Solution:

To address these problems, clean the filter thoroughly, remove dust and debris, and ensure the filter is not damaged. For filter cleaning, follow the steps below.

Step 1: Start by detaching it from the vacuum and gently tap it on a solid surface to dislodge loose particles. 

Step 2: Then, subsequently, rinse the filter with cold water and allow it to air dry before reattaching it. Before attaching, you must check the battery for any signs of damage or wear.

Check this video for more clarity!

Reason 4: Filter Motorhead Failure

Motorhead failure is another big reason for Dyson not working after cleaning. If your Dyson V6, V8, V10, or V11 experiences a complete motor head failure after filter cleaning, it’s probable that the filter was still damp when reattached to the vacuum. 

Moisture from the wet filter could infiltrate the motor’s electrical components. That causes a short circuit and renders the motor inoperative.

Solution:

If the motor head of your Dyson has been damaged due to water exposure, the sole solution is to replace the entire motor unit. You can reach out to Dyson’s customer support to inquire about their repair or replacement services. 

Alternatively, seek assistance from a local appliance repair specialist who can source and install a new motor head. Once the motor head is replaced and functioning correctly, your Dyson V10 vacuum will be ready for regular use.

Reason 5: Battery Damage

Another prevalent cause for your Dyson vacuum’s malfunction post-filter cleaning is a damaged or defective battery. Verify the condition of your Dyson’s battery and ensure it is functioning correctly. 

Solution:

If the battery is found to be faulty or damaged, there is no DIY method that can fix it. You have to replace the damaged battery with a new one. Replacing the damaged component is also a feasible solution to the Dyson V10 trigger not working.

Reason 6: Inside Obstructions

Having inside obstructions is another significant reason for not working Dyson. Blockages within the vacuum can also lead to a malfunction. 

Accumulated dirt in various vacuum components can create obstructions. That triggers pulsating to prevent continuous motor operation and potential damage.

If you notice irregular behavior or the vacuum not functioning when you activate it, be aware that pulsating can be detrimental.

Solution:

To address this issue, follow the steps below: 

Step 1: After cleaning the filter, dismantle all components and attachments of the Dyson V10.

Step 2: Carefully examine the brush bar, wand, and the inlet (where the wand connects to the vacuum) for any blockages.

Step 3: Thoroughly clean and remove any obstructions to ensure unimpeded airflow through each part.

Step 4: This process guarantees unrestricted airflow from the vacuum’s bottom (at the brush bar) to the top (at the filter).

Still Not Working?

If the previously mentioned solutions do not resolve the problem with your Dyson V8 vacuum cleaner, it is advisable to seek professional assistance. 

You can contact the technician team or visit the store where you purchased the machine if you have a warranty card. 

In the event of any hardware or component damage, contacting the technician team for replacement or resolution is recommended.

Conclusion

Hopefully, you got to know why your Dyson not working after cleaning the filter. 

It is common to experience problems with your Dyson after cleaning its filter. You have multiple options to resolve this problem discussed in this article. For further assistance, don’t hesitate to reach out to Dyson’s customer service.